STAHLWERK MIG MAG 200 Doppelpuls Pro fully equipped fully synergic welding machine with AK25 welding torch and AK25 wear parts set

• Extensive, dual pulse function in MIG welding prevents materials from burning through at low root heights and reduces heat deformation. The MIG 200 double pulse Pro welding machine is therefore particularly suitable for welding thin sheets and materials that must only be heated slightly.
• The MIG 200 Doppelpuls Pro works based on an advanced IGBT module with the latest inverter and control technology.
• The MIG 200 Double Pulse Pro welding machine can be used to process and weld non-alloy, low- and high-alloy steels such as steel, stainless steel and aluminum alloys.
• Thanks to the pulse function and advanced torch ergonomics, welding work can be carried out in all known joint shapes (butt welds and fillet welds) and positions (rise seam, down seam, cross seam).
• Convenient selection of twin, spot and continuous spot operating modes as well as other special welding functions.
• The welding machine is suitable for the use of solid welding wire (steel, stainless steel; ø 0.8 - 1.0 mm and aluminum; ø 1.0 - 1.2 mm) and cored wire. This means that a wide variety of materials can be processed and welded.

• Universally applicable 3 in 1 combination device. MIG, MAG and MMA welding is possible up to 200 amps.
• Built-in Volt Reduction Device (VRD) safety feature. To increase safety when welding, the open-circuit voltage U0 is reduced to 14 volts in MMA mode. The welding machine automatically detects the start of the welding process and then increases the idle voltage to up to 62 volts. VRD is factory preset and cannot be turned off.
• Built-in job storage allows you to set preferences and parameters to complete recurring work efficiently and quickly. Jobs and parameters can be restored. This makes it possible to work comfortably without spending a lot of time on set-up times.
• The 2T/4T (MIG) mode allows control of the operating mode and offers extended control over the current flow in the special 2 and special 4 cycle modes.
• Automatic wire feed for precise regulation of the wire feed speed in direct dependence on the set welding current.
• Extensive setting options in terms of current and functions via the intuitive graphic interface in the display.

Note: The device is not intended for use in residential areas where power is supplied from a public low-voltage power supply system. It may be difficult to ensure electromagnetic compatibility in these areas due to both conducted and radiated interference.

Note: Please note that the carbon core was designed exclusively for processing aluminum and stainless steel. When welding steel, please always use a steel core to avoid damage!

• 1 x STAHLWERK MIG 200 double pulse Pro
• 2 x wire guide rollers 0.8 & 1.0 mm with V-profile for steel (already installed in the device)
• 2 x wire guide rollers 1.0 & 1.2 mm with U-profile for aluminum
• 1 x gas connection hose with quick coupling 3 meters
• 1 x ground cable 3 meters (25 mm2; with 13 mm mandrel)
• 1 x professional MIG welding torch AK-25 / hose package 3 meters with Euro central connection.
• 1 x MIG accessory set, 3 pieces (already pre-assembled on the MIG/MAG torch)
  1 x Gas Nozzle
  1 x 0.8mm contact tip
  1 x Gas Nozzle Holder
• 1 x MIG MAG wearing parts set, 28 pieces
• 1 x M6 x 28 x 0.8mm contact tip
• 1 x M6 x 28 x 1.0mm contact tip
• 1 x Wire Brush
• 1 x Assembly Wrench
• 1 x Protective Case
• 1 x welding wire MIG/MAG steel Ø 0.8 mm ER70S-6 SG2 wire roll 5 kg
• 1 x pressure reducer
• 1 x professional welding helmet
• 1 x CH fixed adapter 16A