STAHLWERK MIG MAG 200 double pulse Pro fully synergic welding machine with AK25/MB25 aluminum welding torch and wear parts set for aluminum welding

• Extensive, double pulse function in MIG welding prevents materials from burning through at low root heights and reduces deformation caused by heat. The MIG 200 double pulse Pro welding machine is therefore particularly suitable for welding thin sheets and materials that only need to be heated slightly.
• The MIG 200 Doppelpuls Pro works based on an advanced IGBT module with the latest inverter and control technology.
• The MIG 200 Double Pulse Pro welding machine can be used to process and weld non-alloy, low- and high-alloy steels such as steel, stainless steel and aluminum alloys.
• Thanks to the pulse function and advanced torch ergonomics, welding work can be carried out in all known joint shapes (butt welds and fillet welds) and positions (up weld, down weld, transverse weld).
• Convenient selection of twin, spot and continuous spot operating modes as well as other special welding functions.
• The welding machine is suitable for the use of solid welding wire (steel, stainless steel; ø 0.8 - 1.0 mm and aluminum; ø 1.0 - 1.2 mm) and cored wire. This means that a wide variety of materials can be processed and welded.

• Universally applicable 3 in 1 combination device. MIG, MAG and MMA welding is possible up to 200 amps.
• Built-in Volt Reduction Device (VRD) safety feature. To increase safety when welding, the open-circuit voltage U0 is reduced to 14 volts in MMA mode. The welding machine automatically detects the start of the welding process and then increases the idle voltage to up to 62 volts. VRD is factory preset and cannot be turned off.
• Built-in job storage allows you to set preferences and parameters to complete recurring work efficiently and quickly. Jobs and parameters can be restored. This makes it possible to work comfortably without spending a lot of time on set-up times.
• The 2T/4T (MIG) mode allows control of the operating mode and offers extended control over the current flow in the special 2 and special 4 cycle modes.
• Automatic wire feed for precise regulation of the wire feed speed in direct dependence on the set welding current.
• Extensive setting options in terms of current and functions via the intuitive graphic interface in the display.
• Highest efficiency & performance - Single-phase alternating current (230 V) supplies the device and allows an output power of real 200 amps.
• Smart cooling & overheating protection - State-of-the-art technology, integrated overheating protection and high-performance cooling enable maximum performance when welding.
• Suitable for use with the following shielding gases: 100% Ar, 100% CO2, 2% CO2 + 98% Ar, 20% CO2 + 80% Ar. This ensures efficiency, energy savings and strong arc penetration with low welding deformations.
• The spool mandrel ensures the friction-free holding of 50 mm wire spools and is not suitable for 1 kg wire rolls with 16 mm spool mandrel holder.

Note: The device is not intended for use in residential areas where power is supplied from a public low-voltage power supply system. It may be difficult to ensure electromagnetic compatibility in these areas due to both conducted and radiated interference.

Note: Please note that the carbon core was designed exclusively for processing aluminum and stainless steel. When welding steel, please always use a steel core to avoid damage!

• 1 x STAHLWERK MIG 200 double pulse Pro
• 2 x V-type wire feed roller 0.8 - 1.0 mm - installed. (for steel)
• 2 x U-type wire feed roll 1.0 - 1.2 mm - separately included (for aluminum)
• 1 x Wire Brush
• 1 x Protective Case
• 1 x gas connection hose with quick coupling 3 meters
• 1 x ground cable 3 meters (25 mm² with 13 mm mandrel)
• 1 x professional MIG welding torch AK-25 / hose package 3 meters with Euro central connection.
• 1 x professional MIG MAG welding torch AK25/MB25 for aluminum, 3 meters with Euro central connection.
• 1 x MIG accessory set, 3 pieces (this is already pre-assembled on the MIG/MAG torch): - 1 x gas nozzle, 1 x contact nozzle 0.8 mm, 1 x gas nozzle holder
• 3 x contact tips M6 x 28 - ø 0.8 mm for steel
• 3 x contact tips M6 x 28 - ø 1.0 mm for steel
• 1 x contact tip M6 x 28 - ø 1.0 mm for aluminum
• 1 x contact tip M6 x 28 - ø 1.2 mm for aluminum
• 1 x steel core
• 1 x Assembly Wrench
• 1 x MIG MAG wearing parts set aluminum for AK25/MB25
• 1 x MIG MAG Premium Aluminum Welding Wire ER4043 Si5 1.0mm S200/D200 2kg
• 1 x CH fixed adapter 16A